- 1-807-228-1532
- support@dnb3d.ca
- Free Shipping Orders over $175
- Conditions Apply
Reliable 5015 24V Blower Fan for Rat Rig V-Core 3 Eva 3 toolhead part cooling, Voron 2.4 Stealthburner Clockwork 2, 3D printer fan ducts, electronics airflow, and compact DIY cooling applications.
$24.95
The 5015 24V Blower Fan is a compact 50mm x 50mm x 15mm cooling fan used for 3D printer part cooling, toolhead airflow, fan ducts, electronics airflow, and small machine cooling applications. This product is listed on the dnb3D product page as the SUNON MF5015VX-1L01C-S99, with a brushless blower-style design, MagLev magnetic suspension bearing, 27mm cable, and two-wire black/red leads with no connector.
This fan is especially useful where directed airflow is needed through a toolhead duct or focused cooling path. Your current dnb3D product page identifies it as a Rat Rig V-Core 3 specific part used on the Eva 3 toolhead for part cooling, with 1 piece required for that application. It is also listed as being used on the Voron 2.4 Stealthburner Clockwork 2.
The 5015 size refers to the fan’s 50mm x 50mm x 15mm body. Blower-style fans are commonly used in 3D printer toolheads because they can direct airflow through ducts toward the printed part. This makes the 5015 24V Blower Fan useful for part cooling, toolhead ducts, electronics airflow, and compact cooling paths where a standard axial fan may not provide the same directed airflow.
This fan uses a MagLev magnetic suspension bearing. MagLev fans are commonly valued for smooth operation, quality construction, and reliable performance in compact cooling applications. Your page describes this fan as ultra super quiet, high quality, and dust-free in design.
This fan is listed as a Rat Rig V-Core 3 specific part used on the Eva 3 toolhead for part cooling, with one piece required. It is also listed for use on the Voron 2.4 Stealthburner Clockwork 2. Always confirm your exact printed parts, fan duct, toolhead version, wire routing, and connector requirements before replacing or installing a cooling fan.
The fan is rated for 24V operation and includes a 27mm cable with black and red wires. Your page notes that this version has no connector, which is important for installation planning. Builders may need to crimp, solder, or terminate the fan leads to match their toolhead PCB, controller board, wiring harness, or connector system.
The fan is listed with a speed of 6000 RPM, airflow of 4.8 CFM, loudness of 43.832 dBA, weight of 28.37g, current of 70mA with 81mA maximum, and power consumption of 1.95W. These details make it a compact part-cooling option for printer designs that call for a 5015 24V blower fan.
Although this fan is listed for Rat Rig V-Core 3 and Voron 2.4 applications, it may also be suitable for other compatible 3D printer toolheads, fan ducts, electronics boxes, small enclosures, and low-voltage machine cooling applications that require a 50mm x 50mm x 15mm 24V blower fan. Always confirm fitment, airflow direction, electrical requirements, and wiring compatibility before installation.
For related components, browse the 3D Printer Parts category or the Electronics category. This blower fan can be paired with fan ducts, toolhead PCBs, hotends, extruders, connectors, wiring, silicone socks, and other cooling hardware from dnb3D.
For manufacturer specifications and additional fan details, review the SUNON fan product reference or the SUNON product PDF linked from the dnb3D product page.
Every order is hand-inspected and precision-shipped from dnb3D in Marathon, Ontario. Whether you are replacing a Rat Rig V-Core 3 Eva 3 part cooling fan, maintaining a Voron 2.4 Stealthburner toolhead, building a fan duct, or cooling compact electronics, this 5015 24V Blower Fan provides a practical directed-airflow option for compatible 24V systems.
The 5015 24V Blower Fan is a compact SUNON MF5015VX-1L01C-S99 cooling fan for compatible Rat Rig V-Core 3 Eva 3 part cooling, Voron 2.4 Stealthburner Clockwork 2, 3D printer fan ducts, electronics airflow, and compact machine cooling applications.
| Product Type | Blower fan / 3D printer part cooling fan / compact electronics fan |
|---|---|
| Model | SUNON MF5015VX-1L01C-S99 |
| Fan Class | 5015 blower fan |
| Fan Size | 50mm x 50mm x 15mm |
| Voltage Rating | 24V |
| Current | 70mA / max 81mA |
| Power Consumption | 1.95W |
| Speed | 6000 RPM |
| Airflow | 4.8 CFM |
| Air Pressure | 0.19 |
| Noise Level | 43.832 dBA |
| Bearing Type | MagLev magnetic suspension bearing |
| Fan Type | Brushless blower fan |
| Cable Length | 27mm cable |
| Wiring | 2 wire, black and red |
| Connector | No connector |
| Weight | 28.37g |
| Common Printer Fitment | Rat Rig V-Core 3 Eva 3 toolhead part cooling; Voron 2.4 Stealthburner Clockwork 2 |
| Quantity Note | Rat Rig V-Core 3 Eva 3 toolhead part cooling use requires 1 piece |
| Common Applications | 3D printer part cooling, toolhead fan ducts, Rat Rig V-Core 3 cooling, Voron 2.4 cooling, electronics airflow, control box cooling, small enclosure cooling, and DIY machine cooling |
| SKU | DB-0693-7507 |
| Installation Warning | Confirm 24V fan output, wire polarity, mounting size, airflow direction, duct fitment, cable length, connector requirements, and controller compatibility before installation. |
| Fulfillment | Hand-inspected and precision-shipped from dnb3D in Marathon, Ontario, Canada |
Before installing the 5015 24V Blower Fan, confirm that your printer, toolhead, fan duct, electronics cabinet, or cooling project requires a 50mm x 50mm x 15mm 24V blower fan. Do not connect a 24V fan to the wrong voltage output or an incompatible controller circuit.
This fan is listed with a 27mm cable, black and red wire leads, and no connector. Before installation, confirm how the fan will connect to your printer or toolhead PCB. Use proper crimping, soldering, heat shrink, strain relief, or connector hardware for your build.
Confirm positive and negative wiring before powering the fan. Incorrect polarity or wiring to the wrong voltage can prevent operation or damage the fan or electronics.
This fan is listed for Rat Rig V-Core 3 Eva 3 toolhead part cooling and Voron 2.4 Stealthburner Clockwork 2 use. Confirm your exact toolhead version, printed duct, fan mount, screw clearance, connector routing, and airflow direction before installation.
Blower fans use a directed airflow outlet, so orientation matters. Confirm that the fan outlet matches your printed duct, toolhead mount, electronics enclosure, or airflow path before tightening the fan in place.
Use appropriate mounting screws and avoid over-tightening. Small fan housings can warp if compressed too hard, which may cause impeller rubbing, vibration, extra noise, reduced airflow, or shortened fan life.
Make sure wires, filament strands, printed duct edges, screws, and debris cannot contact the blower impeller. After installation, spin the fan gently by hand and check that the impeller rotates freely before powering the printer or electronics system.
Route the cable away from hotends, heater blocks, belts, pulleys, moving toolhead parts, fan blades, sharp edges, and hot electronics. Use strain relief where needed so the cable and any added connector are not pulled during operation.
Blower fans can collect filament dust, plastic strands, and shop debris. Inspect the fan during routine maintenance and clean carefully with power disconnected. Avoid pushing debris into the bearing or damaging the impeller.
After installation, test fan operation through the printer interface, controller output, or electronics setup. Confirm that the fan starts reliably, reaches expected speed, moves air in the correct direction, and does not make rubbing or grinding noises.
Every order is hand-inspected before shipping. dnb3D precision-ships blower fans, electronics, hotend parts, and 3D printer hardware across Canada from our Ontario facility, helping Rat Rig, Voron, electronics, and DIY printer builders receive clean, usable parts ready for careful installation.
At dnb3D, we don’t just ship boxes—we manufacture solutions. Operating our Industry 4.0 micro-factory in Marathon, Ontario, means your order is handled by the same people who design and test these components.
Ready to Ship (3D Printer Parts & Hardware): Finished, inspected, and on the shelf. Dispatched within 1 to 2 business days.
In-House Manufacturing (Laser, Plasma, 3D Prints): These items are manufactured “fresh” to order. Please allow 3 to 5 business days for precision cutting and finishing.
Custom Projects: Bespoke designs require a consultation and a locked-in timeline before production begins.
We ship nationwide across Canada and the USA. Centrally located on the North Shore of Lake Superior, we are uniquely positioned to get your products moving quickly to either coast.
We stand behind every weld, cut, and print. If a product doesn’t meet your expectations, contact the Hub within 30 days. If we wouldn’t put it in our own shop, we won’t let it sit in yours.
Standard Items: Contact us within 30 days for return authorization. Items must be in original, unused condition.
Custom/Personalized Orders: Digitally fabricated to your exact specs (names, custom dimensions, or unique finishes) are final sale once production begins.
Shipping Costs: Return shipping is the responsibility of the customer unless the item arrived damaged or defective.
Have questions about a specific build? Click here to contact the shop.
